Instructions for updating the software of the Tricolor gs 8304 receiver

The Tricolor TV set, which includes an antenna unit, GS 8304 set-top box, smart card and other components, requires periodic software updates. This is the so-called receiver firmware. It is responsible for correct decoding of broadcast channels in accordance with the algorithms used by the provider, remembering lists and settings, subscriber identification parameters. Receiver firmware may also be required after set-top box software failures. Depending on the user's region, this is done in different ways.

Software update via satellite

To update software via satellite, the receiver must be connected to a configured satellite dish.

PROCEDURE:

1.Unplug the receiver's power cord from the outlet, and then plug the receiver back into the power supply.

2. Switch the receiver to channel number 333 in the general list.

3. After a few seconds, the following message will appear on the screen indicating the need for a software update:

4. When this message appears, select the “Yes” option and press the “OK” button on the remote control. Updating the receiver software takes about ten minutes.

After agreeing to the update, the receiver will go into bootloader mode, and service messages about the software update process will appear on the screen. The type of messages is shown below:

5. When the software update is complete, press the “OK” button on the remote control. The receiver will reboot and enter channel viewing mode.

6. After rebooting the receiver, go to the “Status” menu and make sure that the receiver software version has changed to 1.6.1:

7. Important! After the update, you need to perform a factory reset and search for channels.

To do this, press the “MENU” button on the receiver’s remote control, select “Settings”, then “Factory settings” by pressing “OK” on the remote control.

Confirm resetting the receiver to factory settings by first pressing the red “F1” or “Info” button on the remote control, and then selecting the “Yes” option.

Next, the receiver will reboot and turn on in Setup Wizard mode; go through all the steps of the Setup Wizard.

After downloading the list of regions, select the one that suits you.

Attention! There is no need to select “Main”.

Wait for the channel search to complete and save the found channels.

8. At this point, the software update of the receiver and module is completed, and the receiver is ready for further operation.

Design features

The body of the satellite receiver is silver in color and has a regular rectangular shape. There is a ventilation grill on top. On the left, on the front panel, there are four control buttons:

• Standby is responsible for turning on the device and transferring it from standby mode to working mode and vice versa.
• TV/Radio switches reception modes.
• Channel “↑” and “↓” – two buttons for switching channels.

The display shows the channel number, a special symbol indicating signal reception, TV/radio mode, Standby, mail icon, and the current time.

On the front panel, behind the hinged cover, on the right, there is a slot for installing a DRE Crypt conditional access card.

The rear panel of the receiver is equipped with connectors:

• LNB IN for connecting the converter cable;
• USB for software update;
• CVBS for connecting to the video input of a TV;
• R-, L-audio signal outputs for the right and left channels;
• input for connecting an external network adapter.

. Before Use This receiver is manufactured with…

Page 5

• Image
• Text

Content

1. Before use

This receiver is manufactured in compliance with international safety standards. Please read the safety instructions carefully.

1. POWER SUPPLY

From an alternating current main with a frequency of 50-60 Hz and a voltage of 110-240 V. Connect the receiver only to a power supply with the voltage indicated on the marking.
If you are unsure of the electrical standard in your home, contact your local electrical company. Use only compatible power supplies. 2. OVERLOADING
Do not overload outlets, extension cords or adapters as this may cause fire or electric shock.
3. LIQUIDS
The receiver should not be exposed to liquids, including splashing or dripping.
Do not place objects filled with liquids, such as vases, on it. 4. CLEANING
Disconnect the receiver from the power supply before cleaning.
Use a soft damp cloth for cleaning, do not use solvents. 5. VENTILATION
The ventilation holes on the top of the receiver must be open to allow free air circulation.
Do not place the receiver on upholstered furniture, carpets, sofas, beds or similar surfaces. Do not place other electronic components on the machine. When installing the receiver on bookshelves or cabinets, make sure there is adequate ventilation. 6. CONNECTING THE CABLE FROM THE SATELLITE ANTENNA CONVERTER AND TV
Plug the power cords into the outlets only after all components have been connected.
Disconnect the receiver from the power supply when connecting any cables, TV and other satellite and TV equipment to it and disconnecting all of the above components from it. 7. LOCATION
Install the receiver indoors, avoiding exposure to sunlight and rain.
Do not install it near heat sources or heaters. Make sure that the receiver is located no closer than 10 cm from sources of electromagnetic radiation - televisions, video recorders, etc. Do not place the receiver on unstable surfaces where it could fall. If it falls, it can cause serious physical damage to both a child and an adult, as well as malfunction. 8. THUNDERSTERMS AND LONG BREAK IN USE
Disconnect the receiver from the power supply during a thunderstorm or during long breaks in use. These steps will help prevent damage to the receiver from lightning and power outages.

5

1.1 Safety regulations

Search channels

In the GS 8304, the firmware already contains the necessary settings for searching for Tricolor TV channels.
Additionally, you can set the type of converter - single or universal. If the LNB is single, then the operating frequency of the local oscillator is set to 5150, 9750, 10 600, 10 750 MHz. If the required frequency is not available, you can enter it manually using the remote control buttons. For the universal LNB type, switching between frequencies 9.75 and 10.6 GHz occurs automatically.

Standard converter power is supplied to the LNB IN connector. Increased power supply, i.e. 1 V higher than standard, is used in case of non-standard installation, for example, with a long cable length.

After selecting a satellite, you must enter one of the channels it broadcasts.

To start your search, click Next. Found channels are displayed in the TV and radio columns. Once the search is complete, a message will appear indicating the number of channels found. To finish, press the yellow F3 button. A recording will occur in the receiver's memory.

The search can be interrupted with the red F1 button. In this case, only the found channels will be saved.

Channels are switched using the digital or navigation keys on the remote control or CHANNEL “+” and “-” on the front panel of the satellite tuner.

The volume level is adjusted using the “→” and “←” buttons. They work in all modes. To temporarily mute the sound, press the “Sound” button.

To access some functions of the receiver, you need to know the PIN code, which by default is 0000.

The list of channels when watching TV can be called up by clicking on “OK”. Navigation through the list is carried out using the "" and "↓" buttons. The selection is confirmed by pressing “OK”.

• Tricolor

To exit the list, press “Exit” on the remote control.

TV channel and program data is displayed in the information banner when you switch them or after pressing the red F1 button.

Contents of delivery

1. Satellite receiver.
2. Remote control with two AAA batteries.
3. RCA cable.
4. External power supply.
5. User manual.

The device is activated only if you have an access card.

The connection must be made only when the power of the satellite receiver and connected devices is turned off.

To connect the antenna, you need to connect the converter cable to the LNB IN input of the GS 8304 satellite tuner. In this case, use the F connector.

To connect to a television receiver via SCART, you need to insert one end of the cable into the TV socket of the satellite receiver, and the other into the SCART socket of the TV.

To connect to a TV receiver that has a composite input, you need to connect 3 RCA connectors (white, yellow and red) to the video and audio outputs of the corresponding color (CVBS and L/R) located on the rear panel of the device. The connectors on the opposite end of the cable must be connected to the video and audio inputs of the TV that match the color.

. Before using...

Page 6

• Image
• Text

1. Before use

1. Before use

6

9. FOREIGN OBJECTS

Do not place any foreign objects into the openings of the receiver, as this may cause damage to parts or electric shock.

ATTENTION!

1. Follow the instructions below to avoid damage to the power cord, plug and power supply:

• Do not disassemble or attempt to repair the power cord and plug yourself. • Do not twist or bend the power cord. • Always unplug the power cord by holding the plug, not the cord. • Make sure that the power cord does not pass near heating devices to avoid the possibility of melting the insulation.

2. Follow these guidelines to avoid electric shock:

• Do not open the receiver or power supply housing. • Do not place metal or flammable objects inside the receiver. • Do not handle the power cord with wet hands. • Unplug the power cord during lightning storms.

3. Do not operate a faulty receiver, it may be dangerous. In case of malfunction, contact your nearest service center. 4. Do not place foreign or metal objects into the smart card slot. Doing so may damage the receiver and reduce its service life. This receiver is manufactured in compliance with international safety standards. Please read the safety instructions carefully.

How to flash the GS-8300 receiver yourself

By admin, April 23rd, 2010

GS-8300 Receiver Software Update:

1) Using the Burner program (download here>>), download the receiver software update, file gs8300_hw27_1_0_70_127_beta.upg (download here>>).

Software updating is possible as follows: Downloading software from a personal computer (downloading software directly from the computer to the receiver in which the software needs to be updated)1. Turn off the power to the receiver.2. Connect the RS-232 cable to the receiver and to the PC.3. Install and run the GS Burner program on the PC.4. Find and open a file with the extension .upg (upg file with new software) in GS Burner.5. Press the “START” button.6. Turn on the receiver. During data transmission, the yellow LED on the front panel of the receiver lights up. If an error occurs, an error code will be displayed on the front panel and the receiver will automatically restart with the old version. The GS Burner program window displays the dynamics of the process of changing program data or decoding the error code. If the software change is successful, the receiver will automatically restart with the new version. Do not turn off the receiver while downloading!

Core module software update:

2) Flash the new core module software from the SD card. 2.1) Insert a blank SD card (SDHC, 6 Class, Kingstone or Transcend) into the GS8300 receiver “on the go”. The receiver will automatically format the card. (This will not happen if the card has already been formatted) 2.2) Copy the update file update.otm (download here>>) to the SD card. (With the help of a card reader; in addition to the SDHC card, you also need a card reader for it) 2.3) Insert the SD card into the switched off receiver. 2.4) Connect the GS8300 receiver to the network. After loading, the receiver will begin updating the core module software (6 stages). (you may need to go to Menu->Conditional Access->DRE crypt NPR, and only after that the update process will begin)2.5) After the receiver completes all 6 stages (message 6\6 100%) - remove the SD card2.6) Remove from the card update.otm file, if you are no longer going to update the core module with the card 2.7) Reboot the receiver.

Attention! Do not turn off the power to the receiver while updating the receiver or module software! It is recommended to update both the software and the core module. Headings: Equipment Tags: How to flash the GS-8300 receiver yourself, how-to-flash-the-gs-8300 receiver, firmware 1.0.70 for gs-8300, download firmware 1.0.70 for gs-8300

Headings: Equipment Tags: How to flash the GS-8300 receiver yourself, how-to-flash-the-gs-8300 receiver, firmware 1.0.70 for gs-8300, download firmware 1.0.70 for gs-8300

Why is this necessary?

The software gives the user an interface to interact with the functions that are offered by the supplier. Large update packages from TricolorTV allow you to upgrade the receiver to use new services, such as Multiroom or Cinema, as well as correct errors that arise in the operation of the previous version of the software and make viewing difficult.

In addition, when new services are implemented, the software of the receivers may change, and a non-updated version may simply not support the functions that you want to use. This even leads to blocking access to certain subscription channels, general system lags and equipment failure. The introduction of new channel encoding also requires updated software that could withstand the increase in satellite communication throughput.

It is recommended to check for updates every couple of months. In addition, TricolorTV posts the dates of expected updates on its website - you should not ignore them, otherwise you may miss your favorite TV show one fine evening or be left without access for a couple of days (remember that calibration and new channel search can take up to 8 hours) .

Replacing the program via USB connector

It is important that the firmware of the GS 8304 receiver is not interrupted by turning off the power supply to the tuner or removing the flash drive. The procedure is as follows:

The procedure is as follows:

1. Write the firmware update img file to the root directory of the USB flash drive.
2. Turn on the device and make sure that any channel is working.
3. Insert the flash drive into the USB connector of the tuner.
4. A message will appear indicating that the download process has begun.
5. After its completion, the receiver will notify you that the software download has completed.
6. Remove the flash drive from the USB connector.
7. Press the “OK” button on the remote control. The update is complete.

What else you need to know about manual installation

The required update file is called update.otm. When copying it to a flash drive, it is important to remember that there should not be any more information on it. There should also be no folders or arbitrary renamings. In general, manually installing an update is not so difficult, but it requires a little more time and a free USB drive. The same applies to the module, which is updated many times faster.

Even if the receiver works without failures, it is recommended to monitor updates, otherwise if the need arises for flashing, the procedure will become somewhat more complicated. In addition, it is important not to forget about updating television channels on the Tricolor TV GS 8304. The need for this arises if you want to find new television channels, after maintenance work (can be carried out once or twice a year), during the first setup, changing the frequency of certain channels.

Channels are updated using the remote control via Menu – Channel search – OK. Further, focusing on prompts from the TV screen, the process takes place virtually automatically. This action does not require calling a specialist or additional devices.

From a USB drive

In cases where your Tricolor TV GS 8304 receiver does not have a connection to a satellite dish, the software is updated from a USB drive. Before you start, it is important to format the flash drive in FAT32.

Updating algorithm from a flash drive:

• Preparing a USB drive (formatting) via a computer or laptop;
• Download the required file with the current update for your receiver model from the official Tricolor TV website;
• Unzipping the downloaded file to your computer (laptop);
• Copying the unzipped file to a formatted flash drive unchanged (files cannot be renamed);

• Inserting the drive into the USB connector of the GS 8304 receiver and turning it on (it is possible to connect the receiver directly to a computer via an RS-232 cable);
• Once the file is opened, it will begin updating automatically. The process will be displayed on the TV screen;
• Upon completion, the drive should be removed, the receiver should be rebooted and the software module should be updated;
• To do this, turn on the receiver, reinsert the same drive and start updating the module. Upon completion, reboot again.

How to update the Tricolor TV GS 8300N receiver manually?

The Tricolor TV set-top box is a complex device that is controlled by a whole range of programs. Manufacturers of such equipment are constantly developing new technologies, expanding the range of functions.

In order not to buy another set-top box again and again, it is possible to update old software.

Moreover, owners of receivers of the GS 8300 model, as well as all its configurations, can do this themselves.

cares about its clients and monitors the quality of services provided. Qualified specialists regularly check the operation of the software, eliminating errors and shortcomings, and also create new conditions to ensure consumer comfort.

This is how new versions of software appear with built-in improvements. After the user reflashes the receiver and module, he receives more advanced and modernized equipment that meets the latest trends in digital television.

In addition, the quality of signal reception and transmission of TV channels is improved.

After recent firmware updates for the Tricolor receiver, owners of the GS-8300, GS-8300M, GS-8300N and DRS-8300 models were presented with an improved interface for the “Cinema” function, an optimized section of the “Status” menu, a detailed description of payment, and a detailed explanation of how to improve reception signal for tuning TV channels, as well as an improved process for blocking unnecessary channels.

How to update the Tricolor TV set-top box

Each user can reflash the software of the set-top box and module manually, thanks to detailed instructions on the website and prompts on the screen. You can do this in two ways:

• via satellite communication;
• using a computer.

From satellite

If for some reason you missed the previous system update, this method will not be available to you. In this case, you will need to contact the Tricolor TV support service, or download the appropriate version on the official website and reflash the set-top box via a PC.

If you ever have to do this, here are recommendations on how to update the firmware of the Tricolor TV GS-8300n receiver:

Important! Do not under any circumstances disconnect the receiver from the power supply until the update process is completed!!! This may cause equipment damage!!!

Using a computer

The software update method via PC is suitable for the following modifications:

• GS-8300;
• GS-8300m;
• GS-8300n;
• DRS-8300.

The sequence of actions is as follows:

Sometimes after flashing the receiver, it “does not see” the remote control. In this case, you need to turn off the remote control using the red Standby button, and then press it again to turn it on.

If the update process failed for some reason and you were unable to complete the flashing, or if you accidentally disconnected the receiver from the network, be sure to call support or call a specialist at home.