Setting up the selecline lm t006 remote control

Photo of the Selecline lm-t006 universal remote control

Reviews about “Universal remote control Selecline lm t006”

I lost the instructions for the remote control. Where to find codes. How to set it up?

Evgeniy, in the next couple of days we will post instructions for setting up the Selecline universal remote control and codes for it

Evgeny, try to do this. AUTOMATIC CODE SEARCH Turn on the device you have chosen, for example, a TV and point the remote control at it. Press and hold the desired device selection button, for example, "TV". After 3 seconds, when the indicator lamp lights up, release the button. On the remote control, press and release the “POWER” button. The remote control will begin sending a power-off signal, cycling through the codes in ascending order every two seconds. The light flashes while the signal is being sent. When the TV turns off, quickly press the "OK" button. The indicator lamp will go out and the device code will be saved in the remote control memory.

If it works, write it down

Cool, everything worked, thank you.

Thanks for the instructions on setting up the Selecline universal remote. I couldn't find them anywhere until I saw them on your site. The remote control was lying around idle and the instructions for it were lost, but I couldn’t find what I needed anywhere.

Thank you very much for the instructions for the remote control. I searched the entire Internet.

I tried for a long time to connect this Selecline universal remote control to my TV - I only found instructions on this site. Thank you.

The remote control scans everything, turns off the TV and stereo system, press OK, then your remote control does not work.

Evgeniy, try searching in this mode: SEQUENTIAL CODE MANUALLY Press and hold the desired device selection button, for example, “TV”. After 3 seconds, when the indicator lamp lights up, release the button. Turn on the TV and point the remote at it. To select a code, use the “CH+” or “CH-” buttons. Each time you press a button, the remote sends a power-off signal, cycling through the codes in ascending (“CH+”) or descending (“CH-”) order, respectively. The light flashes while the signal is being sent. When the required code is found, your TV will turn off. Press the "OK" button, the indicator lamp will go out and the code will be saved in the remote control. In some modifications of remote controls, searching can be done using the “LEFT”, “RIGHT” OR “VOL-”, “VOL+” buttons, respectively.

Hello! I bought this remote control, but I can’t figure out how to set it up. You need to control the Yamaha Hi-Fi system. There is a Hi-Fi section in the code table, but the remote control only has buttons: TV, VCR, DVD, SAT, AUX, CBL. Which mode should I select to enter the code for Hi-Fi?

Setting up a universal TV remote control

It will all be quite simple to do. It’s possible that nothing will work out the first time, but don’t despair right away.

If you haven't purchased it yet, you can buy it in China at a very low price.

Setup includes several methods:

In the first and second cases, it is important to know the exact model of your TV. Once you know the model, find its code in the instructions. Often there are several numbers for one model. If you don’t have instructions, then below is a table of codes for various TVs and more.

In the event that the device does not start working, you need to try entering a different number for your existing TV model, or use method 3.

If you don’t want to set up the remote control yourself or it doesn’t work out, then you can ask an employee of some electronics store; you just need to know the TV code.

What is a universal remote control

A universal remote control (UPRC) is a small, simple-looking device. Contains a microcircuit inside that allows you to generate signals of different pulses simultaneously.

There are quite a lot of UPDU models on the market, which differ in configurations, price, appearance and control codes. The most popular models are Supra, Huayu, Beeline.

Codes for setting up a universal remote control for use with a specific TV can be found in the document below.

The algorithm for connecting the PU to Smart TV and set-top boxes of older models is no different. There is no need to look for how to set up a universal remote control for a Samsung TV, or find out from service centers how to set up a universal remote control for an LG TV, since the process of adapting the remote control to the equipment does not depend in any way on the manufacturer of the receiver.

What it is

UPDU (used to replace a lost or non-functional TV remote control. If your TV remote control does not work, use the UPDU instead of a broken standard device.

The UPDU will also come in handy if the original remote controls for your device are difficult to obtain. Difficulties often arise when replacing original accessories for equipment. For example, the MTS remote control is sold only complete with a set-top box. Don’t buy a new console every time the remote control malfunctions. In this case, it makes sense to exchange the MTS for a product from another manufacturer. By now, there are already functional analogues of this device on sale that will do the job no worse than the original. Moreover, after setting up the universal remote control, it will be possible to control not only the TV, but also other household appliances.

IMPORTANT! To make the remote control as convenient to use as possible, purchase a remote control with a built-in LCD display or touch screen. Such models are more consistent with the needs of the modern user.

Setting up UPDU

Each UPDU requires preliminary binding to the device. It may not always be obvious how to set up a universal remote. Universal remote controls for LG TV are produced by the same company, but many other remote control manufacturers have a very distant relationship with the model of your TV. There is no remote control suitable for all TV models at once. Each TV and each remote control has its own unique features. However, common models of universal remote controls cover market demands for remote control devices for all popular brands of televisions.

Supra

This device is a popular model for adjusting Samsung, LG, Philips TVs and other models of TV signal receivers. The installation algorithm for Smart TV and older models is the same.

Automatic setup

The remote control device can be adjusted quickly and conveniently. The process of automatic debugging of the UDPU with the receiver is as follows:

Connect the screen to the network.
The remote control needs to be pointed at the TV.
Press the “POWER” button for 6 seconds until the indicator on the UDPU lights up.
When pairing is successful, the volume icon will appear on the screen. Press the POWER button once.
The UDPU is ready for use; you need to check its functionality.

Manual adjustment

If the described method of adjusting the Supra did not help, and you still cannot control the television through the remote control, there is also manual adjustment of the universal remote control for the TV:

In this document, select the code corresponding to the model of the TV signal receiver.
We connect the TV to the network.
We point the remote control directly at the screen.
Press “POWER” and enter the code found earlier.
Do not release “POWER” until the indicator flashes twice.
We try to check each of the buttons on the remote control. If some of them do not work, then you will need to find another code.

Setting up the SUPRA remote control

TV remote control SUPRA

Step-by-step instruction:

Search online for codes for universal TV remotes that match your TV model.
Turn on the TV.
Point the remote control towards the screen and hold down the “POWER” button. Don't remove your finger; enter your TV code at the same time. When the indicator on the remote control blinks twice, release the button.
The supra setup is complete. Check if the TV responds to pressing the remote control buttons. If the device does not respond to your actions, try a different code.

Automatic code search process in the device memory:

Turn on the TV.
Point the remote at the screen.
Press "Power" and do not release your finger for 6 seconds.
After 6 seconds, the indicator on the remote control should light up. At the same time, the volume setting symbol “VOLUME” will appear on the screen. After these signs of successful binding of the remote control to the TV appear, release the “Power” button.
Check if your device is working properly.

HUAYU

This remote control can be paired with any TV, be it an old Philips or the latest model Samsung. The process of pairing with the screen is the same:

We press the “POWER” and “SET” buttons on HUAYU, which enters the UDPU into programming mode. When the equipment is paired, the indicator on the remote control device will be constantly lit.
The command is set by the “VOL” button.
You can exit the setup mode with the “SET” button.

Remote control devices from this manufacturer are suitable for controlling LCD and LED TVs. This scheme is suitable for setting up remote controls from Unimak, which are also quite common among remote control buyers.

Setting up HUAYU PU

The “HUAYU” universal remote control is a convenient and cheap, and therefore widespread device.

It is very easy to set up. English instructions can sometimes be found right on the back of the HUAYU remote control.

Press the "SET" button. This could be the top left button on the panel, or the bottom right button. In any case, the “SET” and “POWER” buttons we need are located along the edges of the device.
Without removing your finger, also hold down the “POWER” button. The steady, continuous light of the indicator lights up indicates that the device has entered programming mode.
Press the “VOLUME” button several times (see also the “VOL”, “+”, “>” symbols next to the “OK” button). Continue pressing the button successively until the “VOLUME” symbol lights up on the screen.
When the “VOLUME” symbol appears, press “SET” twice, then release. This will exit setup mode. After exiting, the indicator should go out.

IMPORTANT! A similar sequence of actions can be applied to the UNIMAK remote control unit. HUAYU will perfectly replace a lost or irretrievably broken LG TV remote control.

Beeline

Early models of remote control devices from this company had many shortcomings, since they could only be connected if the user had a special set-top box. Also, the remote control did not have a “SETUP” button. However, Beeline corrected itself and released an improved version of remote control equipment. The PU has decreased in size, but has acquired a larger number of functional buttons.

To pair the Beeline remote control with the signal receiver, you will need to follow the following step-by-step instructions:

Turn on TV.
Press the “C” and “SETUP” buttons.
We are waiting for the initialization to complete.
When the indicator blinks twice, the buttons can be released.
You can check the functionality of the device using the “VOL” button.

What is a universal remote control

It sounds complicated, but in fact, it is a simple device that creates signal pulses suitable for most TVs and set-top boxes.

Huayu, Gal, DEXP, Supra are considered popular and high-quality manufacturers of UE.

To set them up, special codes are used, which differ depending on the brand of TV, and you can view them on this page.

The universal model will fit a large number of common and popular manufacturing companies, for example, Samsung, LG or Philips.

Differences from a regular remote control

The original remote control and the universal one have two significant differences, which significantly increase the cost of the first - this is its “branding” and quality.

A remote control made by the owner-manufacturer is undoubtedly of higher quality than a Chinese one. However, if the TV is already 5-6 years old, then you will not be able to find a branded remote control for such an old model.

Setting up a universal TV remote control

It will all be quite simple to do. It’s possible that nothing will work out the first time, but don’t despair right away.

If you haven't purchased it yet, you can buy it in China at a very low price.

Setup includes several methods:

In the event that the device does not start working, you need to try entering a different number for your existing TV model, or use method 3.

If you don’t want to set up the remote control yourself or it doesn’t work out, then you can ask an employee of some electronics store; you just need to know the TV code.

How to find out the TV code?

The code is necessary to be able to connect third-party devices with it. These include remote controls, smartphones or tablets.

It ensures device recognition and correct operation. Consists of a unique set of numbers that can be found in this file, as well as in the TV itself. To do this you will need:

login to YouTube;
open settings;
select the option to connect to your phone;
after entering the “Connect manually” section, a blue code will appear;
remember it or write it down.

How to set up a universal remote control

Each device comes with instructions that describe the setup process in detail. We will look at setting up models from popular manufacturers.

Huayu

To configure it you will need:

turn on the TV, point the control unit at it and simultaneously hold down the power and “Set” buttons;
Watch the indicator carefully, it should be on all the time;
use the volume control to set commands;
To exit pairing mode, press the “Set” button.

Automatic adjustment:

turn on the TV, point the remote control at it;
hold down the button indicating the device type;
after the indicator lights up, release it;
press the power button on the UE, this will start an automatic code search;
As soon as the TV turns off, you must quickly press “OK”, this will save the code in memory.

Sometimes the automatic search does not work well, so you need to configure it manually.

Manual adjustment:

after turning on the TV and pressing the “TV” button, the indicator will light up;
releasing it, enter the device code;
after entering the fourth digit, the code will be saved in the device’s memory and the screen will go dark.

Auto-tuning occurs according to the following algorithm:

turn on the TV, point the CP at it, press the button indicating the brand of TV;
hold down the “Set” button and hold until the indicator lights up;
click on channel selection, automatic code selection will begin;
Once the indicator goes off, immediately press the “OK” button to save the found code.

If the button is pressed too late, you will have to do everything again.

The advantage is that by searching through channels, you can regulate in which direction the search will be carried out.

Manual code entry must begin after pressing the “Set” button and the indicator lights up. Enter the numbers you found and click OK. The remote control will remember the specified combination.

Supra

Automatic configuration algorithm:

turn on the TV, point the remote control at it and hold the “Power” button, release after the indicator lights up;
If setup is successful, a volume control bar will appear on the screen
Turn off the device using the Power button.

Manual remote control setting:

find the code for your device in the previously mentioned article;
turn on the TV, point the CP at it, hold down the “Power” button without releasing it, enter the found code;
Only after the indicator blinks twice, release the power button.

If after setting up the universal remote control does not work, contact the seller or service center, there may be a defect.

First you need to double-check the codes and repeat the manipulations; sometimes mistakes are made during setup.

Where to find codes for universal TV remotes

How to set up a universal remote control?

If we also knew which remote control, which manufacturer, it would be possible to say more accurately. Although, the principle of setting up a universal remote control is in most cases similar.

So, we want to teach the remote control to control several devices.

Here's the usual way:

First of all, we find on the remote control the buttons that we will teach” (TV/DVB,Radio,DVD,VCR, etc.)
Find the SET button (may also be called LEARN). We will need these two buttons to configure our device.
In the booklet for the remote control we find the CODE of our device. The code may consist of 4-5 digits. It is advisable to use the code specifically for the device model that we have. If this particular model is not on the list, the code from an earlier model is usually suitable. But it is possible that some advanced functions will not work as intended.
And so, let's start programming. Press the SET and TV buttons simultaneously and hold until the light/indicator on the remote control lights up (usually next to the POWER button).
Then we set the code that we previously found in the instructions. After this, the light should go out and you can immediately use the remote control in connection with the selected device.

If the code did not work or it was not possible to find a similar model at all, many remote controls have an auto-search function. For example, if you press the same SET + TV buttons and wait until the indicator blinks, the remote control itself will begin to try to establish communication with the device. If he picked up the code and some action occurred on the device, then he should immediately press any button on the remote control in order to confirm the found code.

These steps apply to almost all universal remotes without a display. If someone wants a little more comfort in controlling their equipment, then you can purchase such a miracle device as the Logitech Harmony Touch Remote. This remote control practically does not need configuration, as it recognizes any device with infrared control. By the way, the remote control is able to convert the IR signal into a Bluetooth signal, which allows you to use the remote control at a greater distance without pointing it directly at the device. And it even works through closet doors and from another room.

How to set up a universal remote control?

Perhaps now you cannot find a single living space or office where modern household appliances are not used. When it comes to television and radio equipment, it always comes with remote controls. And such devices that make our lives interesting, comfortable and varied are constantly becoming more and more numerous.

In order not to confuse each time which remote control for which device, you can purchase one, but it can turn on and off absolutely all household appliances in your home. Such technical devices have long come into use, but many people are frightened by the fact that they do not know how to set up a universal remote control.

The difference between a regular remote control for a certain type of equipment and a universal one is that inside a small plastic box there is a certain microcircuit that allows you to expand the memory of this device and write commands not to one receiver, but to several at once. Let's figure out how this can be done.

Where to begin?

If you don’t know how to set up a universal remote control for your TV, DVD and other home gadgets, then, first of all, you should look in the box of the purchased remote control. Most often, there are specific instructions that will help you figure out how to set up this particular remote control.

On this piece of paper, which is an instruction, you can find codes with which even a person who does not know how to set up a universal remote control for a TV, stereo system or air conditioner can do it without any problems on their own.

Codes are four-digit combinations of numbers that correspond to a specific brand of household appliance. There are several codes for each of them, and if you fail with the first set of numbers, you can try the next ones.

Active buttons

To set up a universal remote control, we only need a few of the many buttons located on the working surface. These are the TV, SET (or DVB) and POWER buttons. In addition, an important indicator when setting up the remote control will be the signal light, which is present on every universal remote control and is absent on a regular remote control.

Let's start setting up

There are several ways to configure your remote control and if you fail with the first, you should move on to the second and so on. The main thing is not to rush and understand the sequence of actions:

In order to configure the remote control manually without codes, you will need to turn on, for example, the TV on one of the channels. Then, by simultaneously pressing two keys TV and SET, we ensure that the POWER light comes on. Now you will need maximum speed and concentration - very often, about once a second, you should press the POWER button until the TV responds to this press. Most often, the volume level increases. To complete the setup you need to press either TV or SET.
Another method allows you to automatically configure the universal remote. Press SET and TV at the same time and see if the indicator lights up. If everything is correct, you can start entering the four-digit code. If the indicator goes out, then the setup was successful. If it continues to light, the same should be repeated with the following combinations of numbers.
The automatic search is quite simple. We turn on the TV on one of the channels. After this, press the familiar two buttons again - TV and SET and the indicator light will start flashing. After this, you should point the remote control at the TV. If a volume scale appears on the screen, then without hesitation, press the MUTE button or any other button, depending on the remote control. If the light does not blink, then the remote control is configured for this device.

The same algorithm of actions should be carried out with all other household appliances, which can be controlled using a multifunction remote control.

List of R-TV2 codes

Some time ago, the remote control for the Sokol 37TTs6150 TV broke. I had to buy a universal remote control R-TV2 (aka RTV-02). After I programmed it, I stupidly threw out the instructions as unnecessary, relying on excellent memory and the Internet.

But when I needed this instruction again, I doubted that I was entering the correct code and no information was found on the World Wide Web.

After 2 days of active searching, a solution to this problem was found. And this entry is more like a reminder for yourself (just in case). Well, maybe it will be useful to someone too.

Instructions R-TV2 (RTV-02)

R-TV2 (RTV-02) is a universal remote control that contains more than 800 codes for TVs of various brands, including codes for modern LCD TVs. The remote control retains the selected codes even when the batteries are removed.

A. Search for a model.

Press the SET button and hold the desired brand button for 5 seconds. The indicator should flash.
Release the buttons when the VOL signal appears on the TV.
Check the basic functions of the remote control. If they work, the installation is complete. If they don’t work, repeat step 1 or use the second search and installation method.

B. Manual entry.

Press the SET key and the POWER key simultaneously and hold until the indicator turns on.
Enter three digits of the code on the remote control's numeric keypad. After dialing the third digit, the indicator will go out - installation is complete.
If you want to stop setting, release the SET key for a while.

C. Manual code search.

Press the SET key and the POWER key simultaneously and hold until the indicator turns on.
Press the VOL+ key until the maximum volume is reached. Then press the SET key to save and exit the mode.

D. Automatic code search.

Hold down the SET key for about 5 seconds. The search will begin when the indicator turns on.
When the VOL icon appears on the screen, release the key and check other function keys. If switching occurs, the setup is complete. If not, repeat step 1.

Next is a list of codes for the R-TV2 (RTV-02) remote control

Equipment setup

Blog about modems, routers and gpon ont terminals.

Remote control for Rostelecom TV

Continuing the series of articles about Rostelecom TV (IPTV from Rostelecom), I decided to dwell in more detail on the remote control. The remote control on the new Rostelecom TV platform is the same for all set-top boxes, both SML-282 and iptv-hd-101 from Promsvyaz. In principle, this is the correct approach - after all, there is one platform, the functionality is also the same, and accordingly there should be one remote control. This is more convenient for both subscribers and technical support. Separately, I would like to note that the remote control turned out to be unusual, but very ergonomic and easy to use. By the way, when developing the concept of the remote control, the developers immediately moved away from the standard menu control through four colored buttons - red, green, yellow and blue, creating their own control scheme.

The meaning of each button on the remote control for Rostelecom home TV can be seen in the diagram (picture clickable):

The Rostelecom TV remote control is easily programmed for most modern TVs - either through a special code or through auto-search. Let's try both ways to configure the remote control:

During setup, the TV must be turned on!

Setting up the remote control according to the manufacturer's code:

Step 1. Press the OK and TV buttons simultaneously and hold for two seconds until the LED on the TV button blinks twice - with this action you switched the remote control to programming mode.

step 2. Then, using the remote control, dial 4 digits of the code corresponding to your TV model from the table under the spoiler below.

step 3. If you entered the code correctly, the LED on the remote control will blink twice. If the LED lights up for a long time, repeat steps 1 and 2 again.

Step 4. Let's try to control the TV with the remote control - add the sound volume. If the volume on the TV has increased, then the code is set correctly and the remote control is ready to control both the TV and the STB set-top box. Otherwise, try another code from the table.

TV codes: [Spoiler]

Setting up the remote control by automatic code search:

Step 1. Press the OK and TV buttons simultaneously and hold for two seconds until the LED on the TV button blinks twice to switch the remote control to programming mode. Step 2. Enter code 991 from the remote control. Step 3. Press the CH+ channel switch button. Each time you press the CH+ button, the remote control will select a code from the internal list and send the TV a command to turn off. Step 4. As soon as the TV turns off, press the OK button to save the code. If the code is saved successfully, the LED on the TV button will blink twice. The remote control is ready to operate.

If you need to reset the settings of the Rostelecom TV remote control, do the following: step 1. Press the OK and TV buttons simultaneously and hold for two seconds until the LED on the TV button blinks twice to switch the remote control to programming mode. Step 2. Enter code 977 from the remote control. The LED on the POWER button will flash 4 times. Step 3. All special remote settings are removed.

Note: If, when you control an STB set-top box using the remote control, you simultaneously control the TV, i.e., for example, you switch channels on the TV when changing the volume on the set-top box or vice versa, then this means that the control code for the set-top box and the control code TV match. To fix this, you need to change the code by which the remote control controls the set-top box. This is done as follows: To change the code, do the following:

Step 1. Point the remote control at the console.

Step 2. Press the OK and Power buttons simultaneously and hold for two seconds until the LED on the TV button blinks twice to switch the remote control to programming mode. step 3. Select one of the codes: 3220 3221 3222 3223 3224 and enter it from the remote control.

step 4. You have installed a new code.

step 5. Let's try to press the button on the remote control that causes a control conflict with the TV. If the conflict is not resolved, select another code from the table and repeat steps 1-4.

The full table of codes for the Rostelecom TV remote control can be downloaded here.

The complete table of codes for the Rostelecom remote control from SmartLabs can be downloaded here.

The Rostelecom IPTV subscriber directory (television from Rostelecom) can be downloaded here.

How to set up a universal remote control

R»РёСЃС‚Р°РЅС†РеРѕРЅРЅС‹Р№ РїСѓР»СЊС‚ РїСЂРµРґРЅР°Р·РЅР°С‡Р°РµС‚СЃСЏ РґР»СЏ SѓРїСЂР°РІР»РµР ЅРёСЏ С‚РµР»РµРІРёР·РѕСЂРѕРј. РџРµСЂРµРґ С‚РµРј, РєР°Рє РµРіРѕ РєРїРѕР»СЊР·РѕРІР°С‚СЊ RµРіРѕ РЅСѓР¶РЅРѕ РЅР°СЃС‚СЂРѕРёС‚ SЊ RїRѕ RѕRїSЂRµРґРµР»РµРЅРЅСѓСЋ RјРѕРґРµР»СЊ. RќР°СЃС‚СЂРѕР№РєР° SѓРЅРІРµСЂСЃР°Р»СЊРЅРѕРіРѕ РґРёСЃС‚Р°РЅС†РёРѕРЅРЅРѕРіРѕ РїСѓР»СЊС‚Р° С ЃС‚Р°РЅРµС‚ РѕР±СЉРµРєС‚РѕРј РѕЃСЃР»РµРґРѕРІР°РЅРєСЏ РІ СЌС‚РѕР№ СЃС‚Р °С‚СЊРµ.

How to set up a universal remote control...

The 10 in 1 universal remote control is a multi-functional remote control. Using this remote control you can control devices made in the USA, Japan and Taiwan (about 400 brands in total). 1. Control ten types of devices: TV, VCD, DVD, CD, LD, VCR, CABLE, AMP, TAPE, SAT. (TVs, VCRs, DVD players, MP-4 players, stereo systems, amplifiers, satellite tuners, combination devices, air conditioners, etc.

Where to find codes for universal TV remotes - Click!

The Vivanco universal remote control is a remote control designed for televisions and other devices that receive and transmit analogue or satellite television signals. The universal remote control does not reproduce all the functions of the original device, but is suitable for solving basic control tasks - changing channels, changing the sound volume and starting video. All that is required before you start using it is to configure the necessary parameters.

How to set up and connect a universal remote control to your TV...

The times when you could only switch the TV manually are long gone: today all TVs have a remote control, and sometimes more than one. Unfortunately, the remote control is a rather fragile thing: it can break or get lost, and buying a new one can be a serious problem.

How to set up a universal remote control

One of the few remote controls with a very large number of codes for TVs, VCRs, DVDs, receivers, computers, etc. Life began with MAK 2000 and then, as codes were added and new models were released, the numbers changed for the year in which it was released. MAK MAXIM has finished developing the remote control, with modern equipment, it does not work very correctly, it does not perform all the functions, you have to take other remote controls, but with a large mass of equipment that is still working in our home for 10-20 years, a better analogue cannot be found .

How to set up a universal remote control for your TV?

Typically, a universal remote control (RC) is a small box with LEDs, circuits and buttons. It works because the infrared sensor on it transmits the required code to the same sensor in another device. Using it, for example, you can adjust the sound volume, switch channels, change the power of a particular device, and much more. A universal remote control differs from a regular one in that several electrical appliances can be recorded into its circuit at the same time. Today we will look at how to set up a universal remote control for your TV.

How to set up a universal remote control for your TV? Instructions :: SYL.ru

How to set up the TV 139F universal remote control for... - YouTube

Now it is difficult to imagine our life without electronic household devices. We use them all the time: both for entertainment and for solving everyday problems. Often these devices are equipped with a remote control function using remote controls. Every year the number of electronic equipment in our homes increases, and with it the number of remote controls for them too. But very often remote controls get lost, and it takes a long time to find them.

How to program a universal remote

Not so long ago, people could only dream of a remote control that would allow the TV viewer to truly relax without having to get up from a warm sofa every time to change channels, adjust the volume or turn off the TV. In our time, a new problem has arisen. The modern owner of a video and audio system becomes hostage to competition between different manufacturers who use special codes in wireless systems that differ from others. Because of this, even a universal remote control, if not trained, cannot control competitive components.

How to program a universal remote

Tired of juggling three or four different remote controls to control your home theater? Use one universal remote control (RC) to control multiple devices at once. Universal remote controls are usually programmed in two different ways: either by entering a known code or by searching for a code.

How to set up a universal remote control?

How to set up a universal remote control for your TV?

This article provides detailed instructions on how to set up a universal remote control for all TVs. One such device can easily replace all other remote control devices in the house. The UPDU can give commands to various equipment thanks to a special chip that can generate several pulses at once.

Tip 1: How to set up a universal remote control

How to set up a universal remote control? All universal remote controls for TVs, players, air conditioners, barriers and gates work on the same principle. Each button of such a remote control, when pressed, can generate a code for a certain sequence of IR pulses of the remote control, one code out of many. Codes for remote controls are stored in non-volatile memory. The question of how to set up a universal remote control comes down to choosing from a variety of codes one that corresponds specifically to your TV, barrier or other device.

ekimenko-lawyer.ru