Your question:
How to set up the Vityaz TV?
Master's answer:
Setting up TVs involves adjusting channels, color, geometry, brightness and other parameters. Today on TVs, most system parameters are located in the service menu. To adjust such parameters, they must be opened using a special code from the remote control.
To configure the Vityaz TV, you need to go to the service menu. To do this, you need to put the TV into standby mode, then press the AV button located on the front panel, then turn on the TV while holding the button. You can also simply close the contacts of the XN1 connector with the TV already turned on. Select the desired service menu item to configure certain parameters. Exiting their service menu is carried out in the same way as entering, that is, using the AV button.
Set the desired values there to adjust the position of the picture on the device screen. The HSH parameter, that is, the horizontal shift should be set to 24, and the vertical tilt, that is, VS - 24. The vertical image size, that is, VA should be set to 58. Such data is necessary in order to properly adjust the TV image.
Next you need to adjust the color correction. To do this, you need to set the values of the parameters WR, WG, WB to 32. The first parameter is responsible for the red color correction, the second – for the green correction, and the third, respectively, for the blue color. Now adjust the device's signal brightness. See that the value of the Ys parameter is 14, the Yn parameter is 8, Yp is 0, and the Yo parameter is 0. Such parameters set the delays respectively for SECAM, NTSC, PAL and external sources.
Then tune in the channels on the Vityaz TV. To do this, press “Menu” on the remote control, then select “Channel setup”. There you need to select the “Auto Configure” option. If you want to change the order of channels, then select “Sort”. If you want to watch two television channels simultaneously using two built-in tuners, then select the “Picture in Frame” menu item.
To configure the reception of encoded information, go to the “Teletext” menu item. There you can select the items “Brightness”, “Saturation”, “Contrast”. The value of any of these parameters can be adjusted using the volume control buttons located on the remote control.
Next - “DVB-C setup menu”, “Auto setup”, and press the “OK” button. The advent of digital television caused a kind of excitement, as content in digital quality became available to a wide range of users. Recently, this particular area of television has been developing very actively; a large number of offices have appeared that will provide services for connecting and setting up digital television for a fee. The good news is that you can set up digital television on your TV yourself.
- How to connect digital television without a set-top box: 4 options
What you need to connect digital on an old TV
To receive digital television, the following set of equipment is required:
- Old TV. The later a model is released, the easier it is for it to “make friends” with an external tuner.
- Console. It is she who converts the digital signal into sound and image.
- A regular antenna capable of receiving DVB-T2 TV transmissions. (find out in 3 minutes which one is better to choose).
- Cables: antenna (wave impedance about 75 Ohms) and an adapter through which old TVs (such as Goldstar, Vityaz, Rubin, etc.) are connected to the receiver (more on this below).
- RF modulator. It will be required where not just CRT models are used (the use of a CRT does not interfere with the “digital” in any way), but old Soviet-design tube models, whose connection scheme, in principle, does not provide for operation through a “tulip” or the use of other low-frequency inputs.
Editing channels
On the Vityaz TV you can use a convenient function like sorting found programs. After all, sometimes you may not be satisfied with the location of the found TV channels. Therefore, to arrange all your favorite programs in new positions, simply go to the menu and select Edit Programs. Here you will have access to deleting, sorting, changing the name and blocking channels. To do this, use the colored buttons on your remote control. Under each light its purpose is written. Also, often in the menu there is such a function as sorting LCN , it must be disabled or otherwise the list of channels will start with 800, which is very inconvenient.
…
Page 3
- Image
- Text
1 GENERAL INSTRUCTIONS
This Operating Manual applies to the digital terrestrial television tuner.
rovaya “Vityaz DTR-822HD FTA”, designed for receiving and decoding signals from open channels of terrestrial digital television broadcasting of DVB-T/DVB-T2 standards.
♦ Before purchasing a tuner, consult your retailer or digital TV provider
Your region.
♦ When purchasing a tuner, request that its functionality be verified by demonstrating its functionality.
operation of the tuner in all modes provided for in this Manual.
♦ Check the completeness of the tuner in accordance with the section DELIVERY SET. ♦ Check that the tuner number matches the number specified in the tuner warranty card. ♦ Check that the seal located on the bottom of the tuner is intact. ♦ Make sure that the warranty and tear-off coupons indicate the dates of manufacture and sale,
The store stamp and the legible signature or stamp of the seller are required, as they are the basis for free warranty repairs and maintenance.
ATTENTION! Due to the constant improvement of manufactured products, the name
Some functions and menu modes, the designation of connectors, and the performance of certain ergonomic functions for controlling your tuner may have minor differences from those described, which does not have a significant impact on its control and operation.
♦ Transport and store the tuner in its original packaging. ♦ The packaged tuner can be transported by all types of closed transport (except aircraft
Commodity) at temperatures from minus 40 ºС to plus 50 ºС and protected from direct exposure to precipitation, dust and mechanical damage.
♦ The tuner can be stored indoors in the absence of acidic, alkaline or
other aggressive impurities at temperatures from plus 5 ºС to plus 40 ºС. Storing the tuner without packaging is not allowed.
♦ After transporting the tuner in winter conditions, before turning it on, it is necessary to keep it in
at room temperature in the package for at least 4 hours.
♦ The tuner is designed to operate in the following climatic conditions: – ambient temperature from plus 10 ºС to plus 35 ºС; – atmospheric pressure from 86 to 106 kPa (from 650 to 800 mm Hg); – relative air humidity no more than 80% at plus 25 ºС.
POWER SUPPLY
♦ Your tuner operates on AC power ranging from 170 to 253 V, 50 Hz and not
requires the use of a separate voltage stabilizer.
♦ ATTENTION! Do not connect the tuner to a DC power source!
ACCOMMODATION
♦ Place the tuner on a strong, flat, stable, horizontal surface, avoiding
places with high temperatures, humidity, high concentrations of smoke or steam, accumulation of dust, and places where it may be subject to vibration and magnetic fields. Do not expose the tuner to precipitation or direct sunlight.
♦ High-quality operation of the tuner is guaranteed when it is connected to a television antenna or
antenna cable providing the required input signal level.
2 SAFETY AND ENVIRONMENTAL REQUIREMENTS
♦ electrical safety
. ● Do not connect the tuner to a network with a voltage of less than 170 V or more than 253 V. ● The socket for connecting the power cord must be in an easily accessible place. Not
Connect too many devices to one power outlet.
● Disconnect the tuner from the network when connecting and disconnecting it from the TV. When connected
or unplugging the power cord, hold the plug, not the cord. Do not touch the power cord with wet hands. The power cord should be routed away from heat sources. Do not place heavy objects on the power cord.
● Do not allow young children to turn on the tuner without an adult present. ● Do not place containers containing liquids, indoor plants, etc. above/under or near the tuner.
Also, do not allow liquids or foreign objects to get on or inside the tuner.
♦ Fire safety.
● Do not allow the holes and slots in the tuner body to be covered with anything, since
this may cause the tuner to overheat. If the front panel of the tuner is covered with a protective film, remove it for good ventilation during operation.
● Do not leave the tuner running unattended for more than 15 minutes.
Dear buyer
Page 2
- Image
- Text
Open Joint Stock Company "Vityaz"
Republic of Belarus, 210605, Vitebsk, st. P. Brovki, 13a.
Phone 58-84-67
Dear buyer!
Before connecting the tuner,
ATTENTIVELY
check out
with this Operating Instructions.
Your tuner meets the technical requirements of TU BY 300031652.060-2005 “Tuners
"Knight". Technical specifications"
What difficulties may arise
There are times when it is not possible to set up DVB T2 reception. If there is such a problem, you need to make sure that there is no damage to the antenna. If it is intact, you need to check the direction. The antenna should be directed towards the tower. It is also necessary to install it outdoors; if you place it indoors, it will block the signal. If the user does not know where exactly the tower is located, torsion of the antenna will help. It must be moved very slowly and smoothly. As soon as the antenna makes contact with the tower, the device will work.
Attention! There are errors during the automatic channel search process. For example, the receiver found few channels or did not find them at all. A manual search will help.
It is also possible that the TV has found channels, but the quality of their display is very poor. This means that the antenna is turned towards the tower, but the contacts with it are bad. Try moving it a little. This problem can occur in bad weather.
Vityaz CHASSIS MSh-90M
Please enable JavaScript for a better site experience. Setting up a TV usually involves adjusting TV channels, geometry, color, brightness and other parameters. In modern TVs, many system parameters are located in the service menu. They are opened for regulation by dialing a special code from the remote control. You will need.
To put it into standby mode, press the AV button on the front panel, turn on the TV while holding this button. Or close the contacts of connector XN1 with the TV turned on. To configure certain parameters, select the desired service menu items. Exiting it is done in the same way, using the AV button. Set the following values to adjust the position of the image on the TV screen: set the HSH parameter horizontal shift to 24, set the vertical tilt VS - set the vertical image size value VA These settings are necessary to adjust the TV image.
Adjust the color correction on your TV. To do this, set the values of the parameters WR, which is responsible for the correction of red, WG - the correction of green and WB - blue. Next, adjust the TV brightness signal. Check that Ys is set to 14, Yn is set to 8, Yp is set to 0, and Yo is set to 0. Each setting can be adjusted using the audio buttons on the remote control.
Is the advice useful? Not really. Didn't get an answer to your question? Ask our expert:. Add a comment to the article. Characters left:
TV remote control Vityaz
The Vityaz TV remote control has remote control buttons:
Standby button
turning on and off the standby mode of the Vityaz TV
AUTO button
is not used
Mute button
instantly muting the sound
0…9 button
selecting the channel number
-\—\ button
switching to the multi-digit mode for entering the channel number
Button
return to the previous channel
ASPECT button
changes the aspect ratio
AUDIO button
sound system
VOL button
changes the volume
DISPLAY button
displays information
CH button
switch channels
OK button
turns on the selected mode
MENU button
turns on the menu mode
EXIT button
exits the menu
INPUT button
selects the signal source
P.MODE button
selecting a picture mode
S.Mode button
selecting a sound mode
SLEEP
sleep mode timer
FAV
list of favorite channels
FAV button -
selecting favorite channels downwards
FAV+
button selecting favorite channels upwards
EPG button
electronic guide
TEXT
teletext mode
HOLD button
holding a teletext page
TV/Radio button
switches to digital radio mode
SUBTITLE button
turns on subtitles
INDEX button
teletext index page
SIZE button
teletext page size
REVEAL button
calls hidden teletext information
SUBPAGE button
teletext subpages
MEDIA button
On our website you can download TV remote control location and designation of remote control buttons, as well as instructions and user manual
Setting up Vityaz TV
Initial setup of the Vityaz TV
When you turn on the Vityaz TV for the first time, it is recommended to start setting up from the “Initial setup” menu item. When you turn on the TV for the first time, the start menu will be displayed on the screen Select the language for displaying the menu and text prompts / In the “Setup mode” line, you must set the value to HOME. This is a mode for saving energy consumption and increasing the service life of the Vityaz TV. Next, select the country where the TV is located. In the “Tuner Mode” line, you must set DVB-T when using a digital terrestrial antenna, or DVB-C for digital cable television. The “Auto search” line allows you to selectively select the settings of only digital, only analog, or simultaneously both analog and digital TV channels. Selecting the OFF option in the LCN line allows you to record television channels starting from number 001. In the “Auto channel update” line, it is recommended to set the OFF option, since
Vityaz TV lock
The Vityaz TV blocking function allows you to block changes in channel settings, block viewing of individual channels, block buttons on the TV body and introduce an age limit for viewing digital TV channels. The blocking is done in the “System blocking” menu; the default password for the Vityaz TV is 0000.
ELECTRONICS FORUM
When you turn on the TV, the mains fuse FU1 blows. Check the serviceability of the mains filter elements, fuse rectifiers FU and transistor VT. The TV does not turn on, the mains fuse is working. They also check the integrity of the windings and transformer T. There is no image stabilization when the mains voltage changes. They check the elements of the power supply circuit of the frame coils, paying special attention to their soldering. Then use an oscilloscope to check the presence of personnel sawtooth pulses on the pin. Monitor the voltage at the pin.
