Setting up digital television on Philips TVs

Setting up channels on a Philips TV does not require special knowledge. Just follow simple instructions. Automatic channel tuning saves time and simplifies the setup process.

You will need

• Philips remote control

Instructions

• Find the button on your remote control that says “MENU” and press it. From the list that opens, select the “Configuration” or “Settings” section.
• Next, go to the “Settings” item.
  Select Channel Settings. Then - “Automatic configuration” and “Start”.
• Next - “Reinstall channels”. After this, you need to select any country that has an official digital cable television broadcasting system. Some TVs have a list of such countries on the back.
• Now select the “Cable” section, “Settings”. Before starting the search, you need to specify the baud rate mode - “Manual” and set the baud rate.
• You also need to specify the frequency scan: fast or full. It is recommended to install "Quick Scan". You can select “Full Scan”. It will take about 30 minutes and you don't need to complete the next step.
• Set the network frequency mode to “Manual”.
• To find not only digital channels, but also analog channels, set it to “On”. Next, click “Done.”
• Now you need to start the search. To do this, click “Start” and wait for the search to complete. When finished, select “Done”.
• Channel setup is complete. To exit the menu, you can press “BACK” or “TV”. Enjoy watching!

Rate the article!
Instructions

on setting up Digital Television on
Philips
1. In order to set up high-definition digital TV channels on the vast majority of Philips models, press the “Home” (Menu) button on the remote control, the TV menu will open.

2. Select the Installation tab. After clicking the "OK" button, you will move to the second menu field, then go to the "Channel Search" tab.

3. Select Reinstall Channels.

Read also:  TOP 10 best providers in Moscow - Rating 2021

4. In the Country section you must select Finland, Norway or Germany

5. Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”.

6. When choosing a cable TV provider, set it to "Others".

7. Before you start searching for channels, go to settings and set some parameters

8.Set the frequency scanning mode to fast.

9. Set the network frequency to manual mode.

10. Now set the network frequency to manual mode and enter the network frequency from the control panel. Frequency 371.00 MHz

11. Set the baud rate to manual mode.

12. Set the baud rate to 6875.

13. After the settings, return to the previous menus and click the “Start” button.

Setting up digital channels on Philips TVs

(using the example of model 32 PFL5404H)

Depending on the model, the interface and menu items may differ, but the general meaning and procedure remains relevant.

1. Enter the main menu by pressing the button on the remote control and go to the “Configuration” section

Attention! Some models may request a PIN code at one of the setup stages. If you haven't installed your own, try entering one of the standard ones: 0000, 1111, 1234

Read also:  IPTV - Rostelecom set-top box - how to connect and configure

2. Select “Search channels”

3. Select “Reinstall channels”

4. Select one of the Western European countries, such as Germany or Switzerland

Attention! If you do not have Western European countries in your selection, but only Russia and Ukraine, then you need to update the software of your TV. How to do this can be found in Philips support service by calling the toll-free federal number 8-800-2200004

5. Select “Cable (DVB-C)”

6. Select “Settings”

7. Set the transmission speed mode to “Manual”

8. Enter symbol rate 7000

Depending on the model, the item where you need to enter it may be called “Baud rate” or “Symbol value”; if there are several such fields (as in the figure), then enter the speed in at least one of them

9. Set the frequency scanning mode to “Quick scan”

10. Set the frequency difference to 8 MHz

11. Set the network frequency mode to “Manual”

12. Enter network frequency 306000-354000

13. If you do not need analog channels, set the Analog Channels option to Off

14. Click “Finish” and then start the search with the “Start” button

Read also:  TOP 12 Best set-top boxes for digital TV (DVB T2) | Review of proven models 2021 + Reviews

15. If everything is done correctly, the TV should find about 58 TV channels

16. After searching for channels, you need to configure the internal clock of the TV; to do this, return to the main menu and in the “Configuration” section select “TV Settings”

18. Set the clock mode to “Manual”

19. Set the correct time and date

Digital television has undoubted advantages over analogue: the quality of the transmitted picture, greater resistance to interference, as well as other, less important advantages.

However, to appreciate the quality of digital television, you must have a latest generation TV. As an example, let's try to configure digital channels on a Philips TV.

Quick navigation through the article

Installing and updating channels

The next step is that you need to choose whether you will use channel reinstallation on your TV or just update.

• If you choose to reinstall, all already installed channels are deleted and reinstalled. For initial setup, naturally, choose this mode. Digital channels can be configured in the first hundred, followed by analogue ones.
• The update is best used when reconfiguring. In this mode, all installed channels will remain, and new ones found will appear at the end of the channel list.

First time settings

Starting the TV for the first time requires setting the basic parameters.

• Language. Equipment supplied to the CIS market always has “Russian” in the list of languages. Select it, that the interface was in Russian.
• Select the country that matches your residence.
• Time and time zone. The setting will not affect future setup processes. But it is better to set the parameter correctly if you regularly use the timer to automatically turn off the TV when a specific shutdown time is set.

Additionally, minor parameters may need to be configured.

1. Area of ​​use: shop or home. In store windows, the main task of a TV is to demonstrate image quality. The “Home” mode will open up all the capabilities of the TV.
2. Installation location: on legs or wall mount. The TV will adjust the picture and sound for the most correct image and sound reproduction.

Modern Smart TVs, when first set up, also allow you to connect to the Internet and television.

Scan selection

Frequency scanning is possible in two versions: fast and full.

• A full scan will take too long, so set it to "fast". Again, select the network frequency manually and its digital value is 290.00;
• Next, if you want to configure not only digital channels, but also analogue ones, then mark them enabled;
• Finally, click “Finish” and the channel search will begin.

The search usually lasts approximately 15 minutes.
After its completion, you can return to the beginning of the menu and view the configured digital channels. Share this article
with your friends on social media.
networks:

Setting up digital television on Philips TVs

Instruction No. 1

First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware).
If our country is not there, then we will have to put some other one from this list. 1. Click on the icon - “House”

2. select - “Configuration”

3. select - “Installation”

4. select - “Reinstall channels”

5. select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)

6. select - “Digital mode”

7. select - “Cable”

8. select - “Automatic”

9. click - “Start”

Setup takes approximately 5-10 minutes.

Instruction No. 2

Philips TV models 2011

1. Click on the icon - “House”

2. select - “Installation”

3. select “Search for channels”

4. select - “Reinstall channels”

5. select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)

6. select digital mode – “Cable (DVB-C)”

7. In the “Network frequency” line, enter the frequency

8. in the line “Transfer speed” enter

9. Next, select the line “Scanning frequencies”

Setup takes approximately 5-10 minutes.

Instruction No. 3

1. In order to set up high-definition digital TV channels for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Configuration” section

2. Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list, click “Start”

3. Select "Reinstall Channels"

4. In the Country section, you must select Finland; if this country is not in the proposed list, then select Germany

5. Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”

6. Before you start searching for channels, select “Settings” to manually correct the search parameters

7. Set the baud rate to manual mode: 6875

. In the tab, change the transmission speed manually from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab; “Character 2” is left at 0.

8. Now set the network frequency to manual mode and enter the network frequency from the control panel: 290.

9. After clicking the done tab, you will again be taken to the channel launch menu, now you can start scanning

10. If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

How to boost the signal

Modern equipment has wide capabilities, but the signal is often weak. An amplifier is used to improve image quality.

When choosing, take into account the following parameters:

• length to the broadcast source;
• range;
• noise factor – up to 3 dB;
• point of consumption;
• location.

For digital television, choose a device with a supply voltage index of 5V. If the set-top box has the same parameters, you will not need to buy an additional power supply. There are free ways to boost frequencies: changing the location of the antenna, replacing the cable.

For modern models

Modern TVs have advanced configurations. Setting up is more difficult and requires entering additional data. Before starting, it is advisable to request the broadcast frequency from the operator.

Manual method

The method is practically no different from setting up models developed after 2011. It all comes down to the standard instructions:

1. Check the serviceability of the digital broadcasting cable.
2. Click on the house, called “ Home ”
   .
3. From the list of sections, select “Configurations”
   .
4. Go to “Channel settings”
   and activate the manual interaction mode.
5. Click on the “Start”
   , the
   “Digital Mode”
   .
   Then select the digital broadcast transmission method “Cable”
   or
   “Antenna”
   .
6. Switch to the previous section, indicate the frequency and confirm the action performed.
7. Finish searching for TV channels and save the settings.

The network frequency for Philips digital channels can be obtained from your provider. Without a list of frequencies, you will not be able to manually install TV channels. It is worth remembering that lists on the Internet may be unreliable.

Useful: How to set up digital TV via a set-top box

Automatic method

Automatic tuning on modern TVs differs from previous generation TVs. How to perform automatic setup yourself:

1. Check the network cable connection. Turn on the device and go to the menu.
2. Choose "Settings"
   and start searching for TV channels. Then click on the section
   "Reinstall channels"
   .

3. Select the country, in the next window mark the DVB - C
   .
   Open the “Others”
   .
4. Return to the settings, click on “Fast”
   scanning, in the frequency line indicate 290.00 MHz and speed 6.875, the QAM value is 256.
5. Go to the previous menu, activate automatic tuning, save channels.

The instructions indicate general frequency parameters. It is better to check individual indicators with your cable operator. If you enter the data incorrectly, automatic configuration will be useless.

Channel packages

Dom.ru provides its subscribers with more than 200 digital channels, which are divided into several thematic packages. The following table shows the typical division of TV channels; remember that for your city the composition of the sets and the cost may differ.

Manual setting

There is a need for a manual search option when automatic scanning is unsuccessful. But manual tuning will also be successful when there are no problems with the TV and antenna.

1. You need to find out the broadcasting frequencies of the TV tower.
2. Go to the ECTV map. Enter your residential address along with your house number. Find the house on the map and click on it with the left mouse button. A table will appear with information about the two nearest TV towers. The table will contain the following data: TVK number, frequency for both multiplexes, distance and bearing (directivity). Choose any repeater (preferably the closest one). Write down all the data on a piece of paper or do not close the browser on your computer/phone to see the information in front of you.

Now you can move on to configuration.

1. First, get to the broadcast channel search point. Use the auto search instructions above.
2. Instead of the automatic option, select Manual.
3. Enter the TVC values ​​and the frequency of the first multiplex. The frequency must be entered in Hz (hertz). Add three zeros to the value from the table.
4. Start scanning. The TV will scan the frequency and find the first 10 channels. Click "Done" to add and save your settings.
5. Perform similar actions for the second and third (if possible) multiplexes.

Which search mode to use

Any TV can find channels in automatic and manual mode.

• Automatic search. You just need to select “Auto search” in the settings. The TV itself will scan the frequencies and find publicly available channel packages (multiplexes).
• Manual configuration is needed when the automatic configuration did not produce results or only part of the channels were found (10 out of 20). The method will take more time, but does not cause any major difficulties. It differs from automatic in that it is necessary to find out the exact broadcast frequencies of repeaters. Next, frequencies are entered in the settings and the search starts. The procedure is repeated several times (two or three, depending on the region). Each search finds TV channels from one multiplex. Therefore, if there are two multiplexes broadcast in your region, the search will have to be performed twice.

Possibilities

Philips has been producing TVs supporting Smart TV for almost 10 years now.

This option opens up the following possibilities:

watching movies and videos online, without using additional devices;

surfing WEB resources and communicating on forums, social networks and instant messengers;

uploading multimedia files to the physical memory of the TV or to removable media

play games and office applications.

In general, the functions of the Philips Smart TV are comparable to those of a PC or laptop, but with priority for viewing content.

For Philips TVs, in comparison with other “smart” devices, it is worth highlighting the following features:

Powerful hardware (the manufacturer produces only models in the mid- and high-price categories up to 8K OLED TV and does not specialize in budget products)

Branded widget store (Philips maintains its own platform for installing widgets - App Gallery, and downloading from Google Play is also available)

Advanced operating system (almost all smart TVs run on the Android TV platform, but it has been significantly developed and features an original and wider interface compared to the basic Android on set-top boxes)

Also on some Philips Smart TVs produced in 2015. The WebOS operating system was experimentally preinstalled. After a short time, the developer abandoned it in favor of Android.

Antenna connection

• Each TV has an antenna input, marked on the body with the words “RF IN”, “Ant”, “Antenna”. A plug from a coaxial cable is inserted into the connector.
• If the antenna is active, it means it requires additional power. Depending on the TV and antenna, there are two ways to supply power. The first and most standard is connecting an external amplifier, which is connected by a wire to the antenna and plugged into an outlet. The second is “powering” through the antenna cable. Then in the TV settings you need to activate the “Antenna power” setting.

The cable from the satellite dish is connected to the TV receiver through another connector. It is labeled "SATELLITE" and is located next to the terrestrial television antenna input.

Do all Philips models support DTV?

Setting is possible on all models of the famous brand, provided that the TV was released no earlier than 2005.
Since 2011, devices have been produced with built-in tuners for signal reception; previous models receive digital broadcasting through a special set-top box, which is purchased separately and connected to the device. To check whether the TV supports digital processing technology, check the device markings: the presence of the letters “S”, “T”, “N”, “K” indicates that the TV can be configured to receive numbers. The letter "I" denotes the analogue broadcast type.

Frequency form of Dom.ru channels

Digital television "Dom.ru" provides access to channels of all directions. This table provides a complete list of them.

Mobile TV

Mobile TV from Dom.ru is an application for devices running Android and iOS. It is available at the following links:

Mobile TV supports all the functions of Dom.ru interactive television, which allows you to watch your favorite channels and videos in the same quality even while traveling. For uninterrupted operation of the application, you need an Internet connection with a speed of at least 700 Kbps; even outdated 3G networks can provide this.

Authorization in the program is performed by entering the contract number and personal password. Please note that Mobile TV only works in Russia.

Manual search on all models

You can configure your Philips TV for digital broadcasting in strict accordance with the multiplexes that operate in the user’s specific region.

Advice! You can find out the frequencies needed to search for channels on the website rtrs.ru. There is an interactive map here. By selecting a city on it, you can see active multiplexes and their frequencies.

When manually setting up channels on Philips, you will need to switch between separate blocks of parameters. The general procedure looks like this:

• press the Home button with the house icon;
• select the “Settings” section from the on-screen menu;
• the transition is made to the “Channel settings” block;
• select the “Installing channels” item.

Next, the user is taken to the parameters block. Here you need to select the signal source, cable or antenna. Then activate the item “Digital signal: reception test”. A separate menu will open. After launching the “Search for channels” option, the TV system will prompt you to set the multiplex frequency. After entering the value, you need to click the “Search” button and wait for completion.

The found channels are then saved using the corresponding softkey. The system automatically returns to the reception test menu. Here you can click “Search channels” again, set the frequency of the second multiplex and save the found list. It will be added to the existing one.

Why doesn't it find any channels?

Let's look at the main problems that may arise when searching and setting up channels:

1. The first thing to do is check the signal quality. On the remote control, press the [Home] button and select the [Status] section. In order to find all channels, the signal level must be more than 80%.
2. The next step is to check the frequency and network ID. It happens that the TV requests information about [Network frequency] and [Network ID]. You can obtain these values ​​from your provider.
3. Go to [Menu] – [Channel settings], and set the status to [On] in the [Digital channel] section.
4. Try also changing the frequency scanning step. To do this, before searching, instead of [Start], click [Settings] – [Frequency scanning step]. For a slower but more accurate search, set the value to 1 MHz .
5. If none of the above works, you need to reset the tuner to factory settings. Leave only the power cord from the TV in the outlet; all other cords must be disconnected.
6. Turn on the TV and search for channels without cables connected (the CAM module also needs to be pulled out).
7. Next, turn off the TV completely, and connect the antenna and all other cords.
8. Search for channels again.